Keurig k duo plus auto brew instructions12/19/2023 ![]() Place the carafe on the drip tray and fill the water reservoir to the MAX fill line. NOTE: Between brew cycles, the brewer may take about a minute to reheat. The brew is complete when the brew indicator light is no longer illuminated. The brew indicator light will pulse slowly on and off while the brewer is heating, and the light will turn solid once the brew begins. The initial heating process will take about 4 minutes. The cleansing brew will begin once the brewer is heated. Press the brew button to start the cleansing brew. The 4 brew size buttons will blink, press the 8 button - the brew indicator light will blink. NOTE: The clock must be set in order to use the Auto Brew functionality. Use the H/M buttons to set the clock, then press the blinking brew button to confirm the time. Refer to your Water Filter Starter Kit for instructions.įill the reservoir with fresh water to the MAX fill line, and replace water reservoir. If you have a Keurig ® Water Filter, install it now. Place a large mug (12oz minimum) on the drip tray. positioned to the right, left, or Place a large mug (12oz along the back of the brewer to minimum) on the drip tray. The water reservoir can be Plug brewer into an outlet. If (now.hour() = alarm_h & now.For replacement parts, please visit Before You Brew #include "RTClib.h"RTC_DS3231 rtc char daysOfTheWeek = Date and time functions using a DS3231 RTC connected via I2C and Wire lib#include Slowly lifting the board will give you some space to gently disconnect the clear plastic tube of the pressure sensor (don’t worry, it will not retract into the depths of the machine either). I was able to gently pull the wires to allow for more slack, and was able to unplug the connector without the whole thing retracting. It is also connected to the control wires on the front, and the water pressure sensor tube on the bottom. It is held in place by a couple of screws. I was not aware of the exact locations of these posts, so your results will hopefully be much prettier than my experimental ones seen here.Īlright, we have the control board in sight. Then, a little glue and some electrical tape will allow you to cover up this mess once you are done. By cutting around these posts, you will be able to remove that portion of the lid. Don’t forget to unplug the Keurig from power before doing anything!Īs you can see depicted in the photos, the lid atop of the control pod is only being held in place by 3 posts. I decided to forego these approaches, and instead resorted to using a Dremmel to cut the top lid off, thus revealing the control board. There are lots of videos on YouTube on how this can be accomplished, and none claim this to be an easy task. Misc – Safety glasses, well-ventilated work area, Dremmel, voltmeter, wires, electrical tape, hot glue gun, etc.1 - Adafruit Real Time Clock module ( ).Any microcontroller board should be fine, as long as it complies with the I2C protocol, and has 3 digital output pins.1 - Arduino Uno (for prototyping the circuit board layout - not required).I decided to use Arduino-based architecture to tackle this project. While it makes sense, from an architecture standpoint, not to do this due to the need to change the pods every time you want to have a cup of coffee or tea - I still wanted to be able to wake up to my Keurig machine brewing. ![]() Finally, it will turn off the machine.Įven the highest-priced Keurig models do not offer an auto-brew feature. It will reset the locking mechanism to accept the already-placed pod from the night before. The Keurig 30 will be equipped to turn on at a certain time to begin heating the water. ![]() Therefore, I had borrowed some ideas from other Instructables and/or YouTube videos to come up with my own solution. There are several posts online about automating your Keurig coffee maker, but few had all the features and details that I wanted. ![]()
0 Comments
Leave a Reply.AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |